Notification
Go to Home All Tools Compare Glossary Blog Contact

Voltage Drop Calculator

Calculate circuit voltage drop, percentage loss, and cable power dissipation for DC, single-phase AC, and three-phase AC circuits. Compare standard wire sizes and find recommended conductor gauges.

Quick Presets:
IEC 60228 & NEC Ch. 9
Circuit Specifications Real-time Calculation
Electrical System Choose between DC (two-wire direct current for solar, batteries, auto, LED), AC single-phase (120V/230V branch circuits), or AC three-phase (industrial & commercial line-to-line 400V/480V).
Circuit Phase
Nominal source voltage at the main breaker, battery terminals, or transformer secondary before cable transmission.
V
Presets:
Circuit Load Mode Switch between entering continuous operating current directly in Amperes (A) or total connected load wattage in Watts (W).
Current Draw (Amperes) Continuous electric current flowing through circuit conductors to power the connected equipment.
A
0.5 A 50 A 100 A
Physical one-way cable length between source and load. Conductor return loop distance (2× for DC/1-Phase, √3 for 3-Phase) is automatically factored into total resistance.
Distance Value
m
1 m 250 m 500 m

One-way physical distance from source to load. Loop resistance is auto-calculated.

Conductor Material Copper has higher conductivity (100% IACS) and smaller gauge requirements. Aluminium has ~61% conductivity, requiring larger gauge but offering lighter weight and lower cost.
Copper vs Aluminium
Wire Gauge & Size Choose between American Wire Gauge (AWG, standard in North America) and Metric cross-sectional area (mm², IEC 60228 standard globally).
When active, the tool automatically scans all standard wire gauges and selects the smallest safe cross-section that satisfies your voltage drop threshold.
Recommended

Auto-recommend active. Uncheck above to select manually or click any row in the comparison table below.

Advanced Electrical Parameters
Conductor operating temperature, AC load power factor, conduit reactance, and permissible voltage drop limits.
TOTAL VOLTAGE DROP The percentage of supply voltage lost as heat along the conductor run. NEC recommends keeping branch circuits under 3.0%.
2.40% lost along conductor run
Within Limit (≤ 3.0%)
Voltage Lost The total electrical potential lost between source and load terminals due to conductor loop resistance (V = I × R). 0.29 V Heat dissipated in wire
Voltage at Load The actual operating voltage delivered to the load terminals (V_source − V_drop). Must remain within equipment tolerance. 11.71 V Terminal operating potential

Voltage drop is 2.40%, well within your 3.0% maximum allowable drop. Full operational voltage is delivered to load terminals.

Source: 12.0 V
Loss: − 0.29 V (2.4%)
Load: 11.71 V
Power Source 97.6% Delivered to Load Load Terminals
Loop Resistance Total end-to-end electrical resistance of the conductor loop at operating temperature.
0.058 Ω Total circuit R
Power Loss Electrical energy lost as parasitic heat along the wire run (P = I² × R).
1.4 W I²R heat loss
Load Current The continuous electric current flowing through each phase conductor.
5.00 A Calculated draw
Recommended Smallest standard commercial wire size satisfying your max voltage drop limit.
14 AWG Optimal size
Voltage Drop Curve across Distance Interactive curve showing how voltage drop percentage escalates with cable distance. The horizontal dashed line marks your maximum permissible threshold. Threshold: 3.0%
Current Distance Point Max Allowable Threshold

Standard Wire Gauge Comparison Matrix

Comprehensive evaluation of standard conductor cross-sections showing resistance, voltage lost, drop percentage, and pass/fail status.

Compare all conductor cross-sections for this circuit distance & load. Click any row to test that wire gauge.

Evaluated Gauges
Wire Gauge Area (mm²) Loop Resistance (Ω) Voltage Lost (V) Voltage Drop (%) Voltage at Load (V) Status
User Guide & Instructions

How to Use the Voltage Drop Calculator

Calculate circuit voltage loss and determine the optimal wire size in seconds. Follow these simple steps to ensure your electrical circuits operate safely, efficiently, and within recognized code standards.

Step-by-Step Instructions

  1. Select Electrical System: Choose between DC (2-Wire) for solar arrays, batteries, 12V/24V LED tape, and vehicle wiring; AC 1-Phase for standard 120V/230V residential circuits; or AC 3-Phase for commercial and industrial feeders.
  2. Input Supply Voltage: Enter the nominal voltage at the circuit source (e.g. 12V, 24V, 48V, 120V, 230V, or 400V) or pick one of the quick preset buttons.
  3. Choose Load Mode & Value: Switch between entering load current directly in Amperes (A) or total connected power in Watts (W).
  4. Enter One-Way Cable Run: Specify the one-way distance between the power supply and the load equipment in Meters or Feet. The calculator automatically computes total loop conductor distance.
  5. Select Conductor Material: Pick Copper (Cu) for branch circuits and high conductivity, or Aluminium (Al) for cost-effective heavy distribution feeders.
  6. Choose Wire Standard: Switch between AWG (American Wire Gauge) and Metric mm² (IEC 60228 standard).
  7. Review Wire Recommendation: Keep Auto-recommend smallest safe wire gauge checked to automatically pick the most compact compliant conductor, or uncheck to select a custom wire size.
  8. Inspect Results & Visual Curve: Review the live Voltage Drop (%), Voltage Lost (V), Voltage at Load (V), and explore the interactive distance curve and comparison matrix.
  9. Export or Share: Download a professional PDF engineering summary, export data to CSV, copy calculations to your clipboard, or share with teammates.

The Science & Governing Equations Behind Electrical Sizing

  • • Ohm's Law & Conductor Resistance: When electrical current (I) travels through metallic conductors, physical resistance (R = ρ × L / A) dissipates voltage as heat. Increasing conductor cross-sectional area (A) directly reduces resistance and voltage loss.
    V_drop = I × R_loop
  • • DC Two-Wire Circuit Formula: Direct current circuits flow outward on the supply conductor and return through the neutral/negative conductor, requiring a factor of 2 in the distance equation.
    V_drop = 2 × I × L × R
  • • AC Single-Phase Circuit Formula: Single-phase alternating current calculations factor both conductor AC resistance and conduit inductive reactance (X) modified by load power factor (cos φ).
    V_drop = 2 × I × L × (R × cos φ + X × sin φ)
  • • AC Three-Phase Circuit Formula: Balanced three-phase line-to-line calculations use √3 (≈ 1.732) to account for the 120° geometric phase displacement between line conductors.
    V_drop = √3 × I × L × (R × cos φ + X × sin φ)
  • • Temperature Correction Coefficient: Conductor resistance increases linearly with operating temperature: R_T = R_20 × [1 + α × (T − 20°C)]. For copper, α ≈ 0.00393/°C; for aluminium, α ≈ 0.00403/°C.
    R_75°C ≈ 1.216 × R_20°C (Copper)

Tips for Accurate Results

  • • Double the voltage when possible: Stepping from 12V to 24V cuts current in half and drops percentage voltage loss by 75% for identical wire.
  • • Voltage drop calculations do not replace ampacity checks: Always verify the conductor's continuous thermal rating under local electrical codes.
  • • Center-feed long LED strip runs: Feeding power into the midpoint of an LED tape cuts the effective run length and current in half.

Worked Engineering Example: 24V LED Lighting Circuit

An architectural cove installation powers a 24V DC LED strip consuming 96 Watts (4.0 Amperes) over a one-way distance of 15 meters (50 feet) using 16 AWG copper wire. Total loop length is 2 × 15m = 30m (0.030 km). At 75°C conductor operating temperature, 16 AWG resistance is approximately 16.37 Ω/km. Loop resistance R = 0.030 × 16.37 = 0.491 Ω. Total voltage drop = 4.0A × 0.491Ω = 1.96 Volts (8.19% drop). Because 8.19% exceeds the 3.0% maximum branch limit, the tool automatically recommends upsizing to 12 AWG copper, cutting loop resistance to 0.190 Ω and voltage drop to 0.76 V (3.17%), delivering bright, uniform illumination without end-to-end dimming.

Typical Electrical Circuit Sizing Scenarios

Common real-world electrical circuit parameters and calculated conductor performance:

Circuit Application Operating Specifications Conductor & Voltage Loss
12V Automotive Winch 12V DC · 150 A · 4 m (13 ft) run 2 AWG Cu · Drop: 2.3% (Passes 3% Limit)
24V Solar Battery Bank 24V DC · 30 A · 8 m (26 ft) run 8 AWG Cu · Drop: 1.9% (High Efficiency)
230V Workshop Subpanel 230V 1Φ · 40 A · 35 m (115 ft) run 6 AWG Cu · Drop: 2.2% (Passes NEC 3%)
400V Industrial Chiller 400V 3Φ · 60 A · 75 m (246 ft) run 25 mm² Cu · Drop: 2.1% (Heavy Duty Feeder)
Engineering Fundamentals

Conductor Metallurgy & Sizing Standards

Compare the electrical, mechanical, and thermal characteristics of copper versus aluminium, and review the international cross-reference between AWG and metric conductor sizes.

Copper vs Aluminium Conductors

Selecting the right conductor material involves balancing electrical conductivity, mechanical ductility, thermal expansion, weight, and procurement cost:

Copper (Cu) Conductors

Annealed copper is the global benchmark for electrical conductivity (100% IACS, resistivity ρ ≈ 1.72 × 10⁻⁸ Ω·m at 20°C). It provides superior tensile strength, minimal galvanic oxidation risk, smaller conduit fill requirements, and is the undisputed standard for branch circuits, low-voltage LED installations, automotive harnesses, and residential wiring.

Aluminium (Al) Conductors

Electrical grade aluminium (EC 1350) has approximately 61% the conductivity of copper (resistivity ρ ≈ 2.82 × 10⁻⁸ Ω·m). An aluminium cable requires approximately 1.6 times the cross-sectional area of copper to achieve identical resistance. However, aluminium weighs 50% less and is substantially more cost-effective, making it the dominant choice for overhead utility lines and large commercial building subpanel feeders.

Wire Size Standards: AWG to Metric mm² Cross Reference

Comparison of standard American Wire Gauge (AWG) sizes and nearest equivalent International Electrotechnical Commission (IEC 60228) metric sizes with direct conductor resistance at 75°C:

AWG Size Nominal Area (mm²) Nearest IEC Metric Size Copper Resistance @ 75°C Typical Application
18 AWG 0.82 mm² 0.75 mm² 25.5 Ω/km Thermostats, low-power sensors, doorbell wiring
16 AWG 1.31 mm² 1.5 mm² 16.4 Ω/km Speaker wire, short 12V/24V LED strip feeds
14 AWG 2.08 mm² 2.5 mm² 10.1 Ω/km 15A residential lighting and general receptacle circuits
12 AWG 3.31 mm² 4.0 mm² 6.33 Ω/km 20A kitchen/bathroom small-appliance circuits
10 AWG 5.26 mm² 6.0 mm² 3.97 Ω/km 30A water heaters, air conditioners, solar strings
8 AWG 8.37 mm² 10 mm² 2.51 Ω/km 40A electric ranges, small subpanels, hot tubs
6 AWG 13.3 mm² 16 mm² 1.61 Ω/km 50A EV chargers, subpanel feeders, heat pumps

Worked Engineering Case: 12V vs 24V LED Strip Wiring

Consider an architectural cove lighting installation requiring 72 Watts of high-density LED tape over a distance of 10 meters (33 feet):

Case A: 12V DC Supply
  • Current: I = 72W / 12V = 6.00 A
  • Wire Size: 16 AWG (r ≈ 13.46 Ω/km @ 20°C)
  • Loop Length: 2 × 10m = 20m
  • Loop Resistance: 0.269 Ω
  • Voltage Drop: 6.0A × 0.269Ω = 1.61 V
  • Percentage Drop: 13.4% (Severe failure)
  • Result: Visible dimming and color shift along the strip.
Case B: 24V DC Supply
  • Current: I = 72W / 24V = 3.00 A (Half the current)
  • Wire Size: 16 AWG (r ≈ 13.46 Ω/km @ 20°C)
  • Loop Length: 2 × 10m = 20m
  • Loop Resistance: 0.269 Ω
  • Voltage Drop: 3.0A × 0.269Ω = 0.81 V
  • Percentage Drop: 3.38% (Acceptable)
  • Result: Consistent brightness with uniform luminous output.

Takeaway: Doubling the supply voltage from 12V to 24V cuts the current in half and drops the percentage voltage loss by 75% for the exact same wire size and wattage.

Electrical Engineering

AI Electrical Cable Sizing Advisor

Ask AI
Frequently Asked Questions
Education

Understanding Voltage Drop in Electrical Systems

01

The Physics of Voltage Drop

Voltage drop represents the loss of electrical potential along a conductor path caused by its internal resistance and reactance. Per Ohm's Law (V = I × R), current flowing through wire resistance dissipates electrical energy as parasitic heat, lowering terminal voltage at the connected load.

02

DC Two-Wire vs AC Impedance Calculations

Direct Current (DC) circuits experience pure ohmic resistance across both the supply and return conductor paths (V = 2 × I × L × R). Alternating Current (AC) circuits must incorporate conductor AC resistance and inductive reactance (X) in conduits, adjusted for load power factor (V = 2 × I × L × (R cos φ + X sin φ) for 1-Phase, and √3 × I × L × (R cos φ + X sin φ) for balanced 3-Phase).

03

Conductor Temperature Derating

Metallic conductor resistance rises proportionally with operating temperature. At 75°C operating load, copper resistance increases by ~21.6% compared to the standard 20°C laboratory benchmark. Sizing conductors using temperature-corrected resistance prevents excessive in-service voltage drop and thermal overheating.

04

Regulatory Limits vs Safety Standards

Standards such as the US National Electrical Code (NEC NFPA 70 210.19/215.2) and IEC 60364 recommend limiting voltage drop to 3% for branch circuits and 5% total across feeder and branch circuits. Note that while a conductor may satisfy voltage drop requirements, it must also satisfy continuous current ampacity and short-circuit withstand ratings under local electrical codes.

Good to know

Questions, answered

Quick answers about how this tool works.

Voltage drop is the decrease in electrical potential (voltage) that occurs as electric current flows through the resistance and impedance of conductors between the power source and the load. Because every real-world electrical wire has finite resistance, some electrical energy is converted into heat along the cable run, leaving less voltage available at the load terminals.

Under the National Electrical Code (NEC NFPA 70 informational note 210.19(A)), the standard recommendation is a maximum 3% voltage drop on branch circuits, and a maximum 5% total drop across the combined feeder and branch circuit. International standards (such as IEC 60364-5-52 and British Standard BS 7671) generally prescribe a maximum 3% drop for lighting circuits and 5% for general power circuits. Critical low-voltage DC applications (e.g., solar arrays and telecommunications) often target 2% or less.

For a direct current (DC) two-wire circuit, the formula is: Voltage Drop = 2 × Current (I) × Length (L) × Conductor Resistance (r). The factor of 2 accounts for the complete circuit loop: current travels through the supply wire to the load and returns through the negative or return wire. Percentage drop is calculated as (Voltage Drop / Supply Voltage) × 100.

In a balanced three-phase AC system, each phase voltage is separated by a 120-degree electrical phase angle. When calculating line-to-line voltage drop, the geometric vector difference between any two phases results in a factor of √3 (approximately 1.73205), yielding the standard formula: Voltage Drop (line-to-line) = √3 × Current (I) × One-Way Length (L) × Effective Impedance (Z).

Was this tool helpful?

Be the first to rate Voltage Drop Calculator

Tap a star to rate instantly

What do you need to work out next?

Search 278+ free tools by name, or pick a category below. Every one runs instantly in your browser — no signup, nothing to install.

More Utility Tools